Airborne version of the Radarteam Cobra CBD georadar system.

Thanks to a special antenna, it has a very wide frequency range.

Includes transport case and mounts for the DJI M600 Pro drone.

HS Code: 90158020 (meteorological, hydrological, geophysical instrument)

Ruttner water sampler, 1L

Includes:

1L water sampler
internal thermometer, temperature range -10 C° to +50 C°
4m line
drop messenger
messenger release device.
HS Code: 90158020 (hydrological instruments)

The messenger release device is controlled using UgCS SkuHub onboard computer, allowing a fully automated process of remote water sampling.

It is recommended to order a full kit, including

UgCS SkyHub,
UgCS ground control software and training.

Laser Falcon methane detector plus all required components, software, training and services for use with DJI M300 and M600 Pro drones (drone not included).

Despite the rapid progress with different sensors allowing the analysis of water contamination, turbidity, etc. in-situ, water sampling for subsequent analysis in the laboratory will stay widespread in the foreseeable future.

Traditional methods require direct access to the water body and samples are gathered from the shore, pier, bridge, or boat. Acquiring samples at some distance from the bank without a boat or ship is impossible.

A remote sampling system fully integrated with a UAV solves this problem, allowing water sampling at long distances from the shore.

The system consists of:

Ruttner water sampler with volume 1L for DJI M300RTK or up to 5l for heavy lift drones.
Onboard computer UgCS SkyHub enables to control water sampling process in a fully automatic mode. Water sampling missions are planned and flown in automatic mode with UgCS.
Radar or laser altimeter for real-time altitude measurement during the flight to the sampling location where it is necessary to take a sample, and also to control the descent to the required altitude to take a sample from a set depth.
The only specific component developed for the water sampling system is the messenger release device.

The MagDrone R3 is a ultra portable magnetometer to be attached to any UAV with a minimum payload of 1kg.

Recommended applications:

Searching for UXO (UneXploded Ordnance)
Locating buried infrastructure (metal pipes and shielded cables) and power cables under the load
Archaeology
Surveying for any metal objects weighing a few hundred grams or heavier lying underground
MagDrone R3 can be ordered with internal GPS receiver or with connector for the external GNSS receiver. Second option is recommended to achive better geotagging of the data, especially when R3 is used with UgCS SkyHub onboard computer and RTK-equipped drone.

Note, that general rule with magnetometer when it is necessary to detect artificial objects or artefacts - fly as low as possible. Recommended altitude for the tasks like UXO search - 1m above surface or even lower. That means that drone should be equipped with terrain following system (included in recommended magnetometer bundle).

Recommended drones to carry MagDrone R3: DJI M300 RTK, DJI M210, DJI M600 Pro.

What's in the set:

MagDrone R3 magnetometer with 2x triaxial fluxgate magnetic sensors, sensor bar and data recorder
MagDrone Data Tool software
11.1 V Li-Ion re-chargeable battery battery and wall charger (when used with UgCS SkyHub, power is provided from the drone)
USB cable to connect MagDrone R3 to Windows computer
USB cable to connect MagDrone R3 to GPS-out interface of UgCS SkyHub (for configuration with connector for external GNSS receiver)
Mounting plate and screws (used with provided Li-Ion battery)
Set of international power plugs
Manual
Transport hard case
Additional information:

MagDrone R3 datasheet
MagDrone R3 data examples
HS Code: 90158020 (meteorological, hydrological, geophysical instrument)

Packaging information: 112 x 29 x 11 cm, 10kg in transport box

The MagDrone R4 is an ultra light weight magnetometer with 5 triaxial Fluxgates to be attached to any UAV with a 1,5 kg payload.

In opposite to the MagDrone R3, the MagDrone R4 is used for high resolution mapping in order to detect small and compact objects as well as structures in the ground, such as UXO or archaeological features.

Recommended applications:

Searching for UXO (UneXploded Ordnance)
Archaeology
Surveying for any metal objects weighing a few hundred grams or heavier lying underground
Note, that general rule with magnetometer when it is necessary to detect artificial objects or artefacts - fly as low as possible. Recommended altitude for the tasks like UXO search - 1m above surface or even lower. That means that drone should be equipped with terrain following system (included in recommended magnetometer bundle).

Recommended drone to carry MagDrone R4: DJI M300 RTK

What's in the set:

MagDrone R4 magnetometer with 5x triaxial fluxgate magnetic sensors, sensor bar and data recorder
MagDrone Data Tool software
Power supply cable MagDrone R4 (XT30 plug for UgCS SkyHub)
USB cable to connect MagDrone R4 to Windows computer
USB cable to connect MagDrone R4 to GPS-out interface of UgCS SkyHub
Mountings for DJI M300 RTK drone
Manual
Transport hard case
Additional information:

MagDrone R4 datasheet
MagDrone R4 data examples
HS Code: 90158020 (meteorological, hydrological, geophysical instrument)

Packaging information: 112 x 29 x 11 cm, 12kg in transport box

Cable to provide power from UgCS SkyHub to Radarteam Cobra Plug-In GPR system eliminating the need to use of internal battery of GPR.

The cable has an XT30 plug connector for the UgCS SkyHub side and Lemo connector for the Cobra Plug-In side.

Note that the output power selector on SkyHub should be set to 12V to provide power for Cobra Plug-In.

Ultra-sensitive hi-end lightweight magnetometer for UAV.

MagArrow is fully self-contained sensor (with build-in GPS receiver, data recorder and battery), and may be used with any suitable UAV suitable to carry 1kg.

To minimise noises from drone's motors and electronics, it is recommended to use 3m long suspension ropes to mount MagArrow under the drone. For such configuration it is recommended to use larger drones as DJI M600 Pro or similar, with smaller drones (DJI M300 RTK, etc.) we recommend to use extention poles for the drone's legs.

Alternative way is to mount MagArrow right on the legs of drone and use low-pass filter during data post-processing to remove drone's noises. That approach works pretty well for the surveys like UXO search, but for work requires to register weak or long anomalies (archaeology, geology, etc.) it is better to use suspension ropes.

Recommended applications:

Environmental (abandoned wells, pipes, and storage tanks)
Geology - survey for variations in the magnetic field
Archaeology - detect weak anomalies from archaeological features and artefacts
Searching for UXO (UneXploded Ordnance)
Note, that general rule with magnetometer when it is necessary to detect artificial objects or artefacts - fly as alow as possible. Recommended altitude for the tasks like UXO search - 1m above surface or even lower. That means that drone should be equipped with terrain following system (included in recommended magnetometer bundle).

FEATURES AND BENEFITS

Lightweight: Weighs only 1 kg, allowing a flight time 20% longer than a 2.5 kg-payload UAV.
UAS Agnostic: Attachable to most enterprise UASs
Self-Contained: GPS, storage, and WiFi on board. No data connections to UAV needed.
Super-Fast Sampling Rate: Fly faster, up to 10 m/s with samples every 1 cm. Filter out UAV motor noise.
QC in the Field: View and QC data in the field using any device with a web browser app interface.
Low Power: A single 1800 mAh lithium polymer battery will power the system for 2 hours, outlasting multiple UAV flights. Batteries are hot-swappable.
Additional information:

MagArrow datasheet
MagArrow data examples
HS Code: 90158020 (meteorological, hydrological, geophysical instrument)

Packaging information: 122 x 48 x 20 cm, 11kg in transport box

Cable to connect UgCS SkyHub 3rd generation to Inspired Flight IF1200 or new IF1200A drone.

The cable has 2 connectors for the UgCS SkyHub:
- XT30 socket connector (power)
- Switchcraft W16982-7SG-P-518 connector (signal)

Connector for the drone: DB25 with pinout according to the Inspired Flight specifications for "Universal Payload Connector 2.1 25P".

Universal mountings for payloads on ropes/cables: echo sounders, water samplers, etc.

Also compatible with some types of LIDAR payloads.

TOPODRONE LIDAR kit for DJI Matrice 300 RTK/200/210V2 based on Velodyne Puck Lite sensor, high-precision IMU and L1/L2 GNSS receiver is most cost-effective UAV LIDAR system at the market with working range up to 100 m, can provide high-accuracy point cloud.

It is an ideal entry-level survey system and can be used in various industries, e.g. surveying, forestry, powerline inspection, mining and exploration.

The total weight of the system is less than 1 kg.